Other

ReMote Sustain Lever - Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head - Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash - Cable Kind Clamp does not damage secured cables and features captive hardware - Only compatible with Reverb Stealths - Features a leak-proof, robust, and low-maintenance mechanical actuation system - Easy cable detachment for service, travel or bike shipping - 40mm reduction in in-frame height compared to Connectamajig Reverbs

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 8mm - Outer Diameter: 22mm - Width: 7mm

RockShox Sektor DebonAir Assemblies - Includes air top cap, Air spring and shaft bolt

Original equipment ceramic bearing pulleys and inner cage for SRAM XX1 Eagle rear derailleurs.

Paul's dropper trigger with stacked dual sealed cartridge bearings, two different cable clamp options, a barrel adjuster, and a hinged clamp. - Dual stacked sealed cartridge bearings in the pivot for zero slop and long (serviceable) life - Pinch bolt and cable head recess allowing you to run the cable in either direction - Hinged clamp so you can install it without removing the grip - Barrel adjuster for fine tuning the cable tension

RockShox Motion Control IS Compression Dampers

Magura service kits come in a variety of packages to fit your needs.

Ergonomic Legacy II Aerobars feature extensions that provide a variety of hand positioning, and width and rotational armrests with a high stack to achieve a relaxed ride position. Ideal for riders that need extra positions for Centuries. - Injected Venturi Armrest and ZB Bracket - Forged 6061-T6 construction with armrest made of injected nylon and glass fiber - Fixed extension adjustment - Extension angle 44 degrees with 58mm rise - Fits both 26.0 and 31.8mm basebars, shims included

Magura service kits come in a variety of packages to fit your needs.

ELEVENSIX coils are precision manufactured at HyperCo's state-of-the-art USA facility and available in 25lb/in increments for uncompromising setup. Each HyperCoil suspension spring is individually inspected, and laser marked with size and rate information for the ultimate in accuracy!

ELEVENSIX coils are precision manufactured at HyperCo's state-of-the-art USA facility and available in 25lb/in increments for uncompromising setup. Each HyperCoil suspension spring is individually inspected, and laser marked with size and rate information for the ultimate in accuracy!

ELEVENSIX coils are precision manufactured at HyperCo's state-of-the-art USA facility and available in 25lb/in increments for uncompromising setup. Each HyperCoil suspension spring is individually inspected, and laser marked with size and rate information for the ultimate in accuracy!

The Ohlins Stumpjumper Spring sets a new benchmark for spring rate accuracy and light weight for steel springs. - Ultra-fine spring rates to ensure perfect set up for all weights. - Spring rates are broken down to 4 N/mm (23 lbs./in). - Fits Ohlins TTX shock absorber for Stumpjumper FSR only. - Made with proprietary ultra lightweight steel, it's incredible for keeping your build weight down for trail riding.

The new generation spring series features a race-ready weight with big mountain strength. You'll also find advanced technologies that feature a multi-step surface treatment process, as well as cutting-edge heat treatments. Lastly, we use wire materials that allow us to stress the wire harder, without causing damage to the spring, and therefore design lighter springs. - Precise spring rates are broken down to 4 N/mm (23 lbs./in).

The new generation spring series features a race-ready weight with big mountain strength. You'll also find advanced technologies that feature a multi-step surface treatment process, as well as cutting-edge heat treatments. Lastly, we use wire materials that allow us to stress the wire harder, without causing damage to the spring, and therefore design lighter springs. - Precise spring rates are broken down to 4 N/mm (23 lbs./in).

The Ohlins RXF 36 Coil Fork Spring sets a new benchmark for spring rate accuracy and light weight for trail and all-mountain fork springs. - Ultra-fine spring rates to ensure perfect set up for all weights. - Spring rates are broken down to 0.9 N/mm (5 lbs./in). - Fits Ohlins RXF Coil fork only.

• Converts a cassette hub to a single speed • 8 spacers included in various sizes to adjust chain line • Anodized 6061 aluminum • Fits Shimano/SRAM cassette bodies • Conical spacers for increased cog stiffness • Includes single-speed guide, spacers, as well as 18T & 16T cogs

Replacement lever blades for Magura disc brakes

- EW-WU111 D-Fly wireless transmitter - Shifting customization, system diagnosis and firmware updates can now be done through Bluetooth Smart on smart phones and tablets, using the eTube app - Also allows to send shifting and system data to compatible cycle computers via private ANT+ protocol - Requires BT-DN110 internal battery or BM-DN100 external battery mount

Expand your choice of cranks for use in frames with 41mm ID shells. Replace your bottom bracket with these dual-row flanged bearings and run 30mm spindle cranks in your frame. These bearings fit directly in frames with 41mm ID bottom bracket shells. Crankset spindle length must be longer than 104mm when used in a 86.5mm wide BB shell. - Sold individually (two needed per frame) - Bearings: Enduro Dual-Row ABEC-3 - Color: Silver - Bottom Bracket/Frame Interface: BB86, BB92, PF90, BB104/107, PF121, PF132 - Bottom Bracket Shell Width: 86.5mm – 132mm - Bottom Bracket Shell I.D.: 41mm - Flange OD: 42mm - Crank Spindle Diameter: 30mm - Over Bearing Width: 92mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Weight: 36g

- Provides enhanced chain retention for all 1x drivetrain systems - CNC machined AL6061 alloy mount with dual-compound chain guide - Co-molded composite and TPR guide plates greatly reduce noise from chain contact - Compatible with 28-38T circular and 26-36T oval chainrings - Boost-compatible - Easily adjustable - Mounting hardware included

Flip-up armrest leaving the base or drop bar clear for riding with your hands on the flat section of the handlebar. - Construction: 6061-T6 Forged Aluminum - Stack Height: 24mm - Width Adjustment: 37mm - Clamp Diameter: 31.8mm (26.0 w/Shims) - Weight: 242g

The forged aluminum bracket offers solid, easy-to-use construction alongside an industry-leading fit range. It is also compatible with our riser kits. The bracket is designed for 31.8mm bars and 22.2mm extensions in aluminum or carbon. - Materials: Forged 6061-T6 AL - Stack Height: 42.6mm - Width Adjustment: 37mm - Basebar Clamp Diameter: 31.8mm - Extension Clamp Diameter: 22.2mm - Weight: 234g

Force eTap AXS Rear Derailleur Pulley Kit - Steel bearings - 12-Speed

Original equipment rear derailleur pulleys and inner cage for SRAM X01 Eagle rear derailleurs.

• 6061-T6 tubular aluminum construction • Laser etched graphics • Independent arm rest and bar adjustment • Does not include armrests • Cannot mount shifters onto ends • Clamp diameter: 25.4-31.8mm • Extension length: 105mm

Master cylinder assemblies for Magura brakes include a master cylinder, lever blade and handlebar clamp. Hose fittings and line are sold separately. Flip flop design allows unit to be mounted to either the left or right side.

Air Can Assemblies for repair and maintenance of Rockshox rear shocks.

Air Can Assemblies for repair and maintenance of Rockshox rear shocks.

Air Can Assemblies for repair and maintenance of Rockshox rear shocks.